Tweet
one inch radius?
Now this is safe!!
Now this is safe!!
-
-
[QUOTE=guedo499;218196]Try this one on for size.
I just drew it out on my hydro, seems I have to remove quite a bit of tip & air dam. There will be a hole to fill too so I guess Ill have to make end caps or foam it in.
From what I gather on this I should block sand the narrow [side] part of the tip till 3/4 flat, compass out the 2" dia & trim it back. I'll have to reshape the air dams a bit too but meant to do that anyway. Question is does the 3/4 need to be dead flat or will some creative rounding over be acceptable?Team TowerComment
-
My interpretation would be that the 3/4" area would have to be flat. Any creative rounding could only be done on areas thicker than, or outside of the 3/4" area.
I'll check with the other members of the Stock Outboard "Boat Technical Committee" and get back to you ASAP.
FYI - I am the chairman of that committee.John Runne
2-Z
Stock Outboard is all about a level playing field.
True parity is one motor per class.
It's RACING, not just another boat ride!
NOT a representative of Racing Outboards LLC.Comment
-
Thanks John, to be safer & aerodynamic.. [as if I knew]Originally posted by csh2z View PostTeam TowerComment
-
69ab8c0e293252ac91af69513c3284.jpgOriginally posted by csh2z View Post
This is the part im not getting.. There should be no Interpretation.. How bout some specifications... If your not in the "click" or good old boy club your stuff will probably not be interpreted in your favor..Comment
-
The yellow box in the drawing says "STOCK OUTBOARDS AND J CATEGORIES"
So are modified outboards exempt from this new rule?
Comment
-
The 3/4" area is to be flat, as stated earlier.John Runne
2-Z
Stock Outboard is all about a level playing field.
True parity is one motor per class.
It's RACING, not just another boat ride!
NOT a representative of Racing Outboards LLC.Comment
-
The new rule will now be in effect as of Nov. 1, 2013 for the Stock and J categories.John Runne
2-Z
Stock Outboard is all about a level playing field.
True parity is one motor per class.
It's RACING, not just another boat ride!
NOT a representative of Racing Outboards LLC.Comment
-
Ok boys and girls you can put the chain saws away for now
Destiny is a matter of chance,it is a matter of choice; it is not a thing to be waited for, it is a thing to be achieved.Comment
-
Thats funny george.. I was thinking SawsallOriginally posted by G Stillwill View PostOk boys and girls you can put the chain saws away for nowMike - One of the Montana Boys
If it aint fast make it look good
Comment
-
John is this true for J Categories also? Did they re-vote also?Originally posted by csh2z View Post"Ask anyone, I have no friends. I do have some people that put up with me and mostly because they like the rest of my family"
Don AllenComment
-
A wise old General that I worked for told me one time that "order, counterorder, leads to disorder". Couldn't help but pass that along. Having said that, I think the right thing is now being done. Thanks for all the effort and attention. Jack
Comment
-
Don,
I'm not 100% sure but I was told that the J committee would follow our lead.
It's on the internet, it must be true!John Runne
2-Z
Stock Outboard is all about a level playing field.
True parity is one motor per class.
It's RACING, not just another boat ride!
NOT a representative of Racing Outboards LLC.Comment
-
You said it all John.. The internet never lies!!Originally posted by csh2z View Post
Mike - One of the Montana Boys
If it aint fast make it look good
Comment
-
Thats good, 'step away from the boat' who knows, could be in a new boat by then. LoLsOriginally posted by G Stillwill View PostOk boys and girls you can put the chain saws away for nowTeam TowerComment
Comment