15mm > 9/16" adapters.

[bh/]

Steel race prop bushings

15mm to 9/16" [ABC]
11/16"[D] to 15mm
16mm to 11/16" D

$20 post paid to anywhere in NA

Blank 80/102/302 lower unit adapters;
$50 post paid
bhendrick@earthlink.net

[Bob Dunlap]

Wrong Adapter

That's great bh do you also have the one that goes from 11/16" to 15mm.

[bh/]

That's great bh do you also have the one that goes from 11/16" to 15mm.

Bob; I have a few large ones left over from some we made last year. I could send you one, or run off more if there was a need?
11/16" >15mm is easy as the wall thickness is about 50thou, but the 15>9/16" one is only ~0.015".
Means they must be tough steel, and a sliding fit into the prop and over the shaft , as one does not have much to pound on..

[sam]

I wonder if there is a Redi Sleeve or Speedisleeve that is the right size?

[bh/]

I wonder if there is a Redi Sleeve or Speedisleeve that is the right size?

If there were it would be good to know. I do not have access to a catolog. 'D' to 'ABC', ie; 11/16" to 9/16" is easy,
and are probably stocked by your local TSC store.
Its the metric switch that puts us out in left field,
but if there is a commercial application other than ours,
it would be a lot easier and cheaper than what I am doing.

[Bob Dunlap]

Catalog!!!!!!!!!!!!!!!!!!!!!!!!

Come on bh you live in the modern age of computers, you have the internet, you can find anything there. I have looked for ready made bushings several times with no luck

[STEVE FRENCH]

Brian,
Need one of each....send invoice.....Thanks!.....

567 Maple ave.
Clymer, Ny. 14724

Also look'n for 302 adapter plate to Bayer tower.

Rigg'n 202 with silenced chamber to Tunnel Mite for GT-MOD lake Racer
.
.

[STEVE FRENCH]

Brian,
Send P/M so I can git check out to ya ?
.
.

[bh/]

Brian,
Send P/M so I can git check out to ya ?.

Sent; -but I don't need no check til yu git all the parts.

[STEVE FRENCH]

Brian,
Sleeves arrived.
The 15mm x 9/16" is perfect.
Not sure on the larger one....?...Need one to go from "D" size to 15mm.

Will send check for small one ($21.38?) and return the other.
Need address/amount.

[bh/]

Brian,
Sleeves arrived. The 15mm x 9/16" is perfect.
Not sure on the larger one....?...Need one to go from "D" size to 15mm.

Steve; - i only sent one, the 15mm>9/16".
The larger one is the "packing sleeve".
I am sorry, but I do not trust the USPO handling my stuff.
The 'large' one is hack-sawed from the frame of a bicycle made in Korea. It may be close to a D>15mm bushing,
I did not check.
Keep your $$ 'til I send u a real one.

[bh/]

Steel race prop bushings.
15mm to 9/16" [ABC]
11/16"[D] to 15mm
$20 post paid to anywhere in NA

Blank 102/302 lower unit adapters,
$50 post paid
bhendrick@earthlink.net

D bushings and Yamato adapters now available

[lakeracing35]

D,and E parts for sale

One mercury quicksilver new gears One 40c Mercury D Complete with down houising One Mercury 44E complete with down housing Plus new mags caps and bottoms and all kinds of stacks and fuel parts. Contact Jeff Lake at 217 316 8912

[nbranews]

This is all good equipment. I beleive the area code for Jeff's phone # is 217.

[bh/]

D bushings and Yamato adapters now available

We now have some 16mm to 11/16''
bushings for those who wish to run a
D wheel, 11/16", on the 16mm OEM Yamato shaft.
Either drill the prop to a forward pin,
or drill the shaft to accept rear pin.