Tweet
The following shows the inventory of my spare/excess Mercury "D" Mark 55H Quicksilver Gearcase parts and assemblies that I am going to sell off to Collector(s) or to Racer(s). I have not made a decision if I am going to part out the entire lot of 1 complete Mercury Mark 55H complete and near 2nd complete gearcase assemblies here plus lots of spares or sell it as a package deal to one buyer for everything as I don't want to be left with any repair/replacements parts for my existing Modified Merc engines. My posterity/museum engines will never need these either.
The all inclusive list is as follows:
1.) Merc 55H stock dimensioned gearcase with loose rear cone threads, needs oversized cone and re-thread job. Good bearing areas throughout otherwise.
2.) Merc 55H stock dimensioned gearcase requiring the drivehaft bearing (Torrington roller) area be sleeve/bused and new Torrignton drivehaft bearings installed. Cone threads and other bearing areas are in good shape
3.) 2 Piece coupled Mercury Mark 55H driveshaft for standard height stock racing setup but can easily be cut and re-joined for shorter Modified applications/transoms.
4.) 3 of Mercury D propshafts with mounted gears. 2 shafts in good shape with their gears, 1 shaft is fair condition and likewise its prop gear.
5.) 3 of Mercury D propshaft mounted propshaft gears. All 3 are used but in condition from 95% to 90% and final down to about 80% of gear wear left.
6.) 4 of Mercury D driveshaft gears. 2 are in good used condition with 90%+ gear wear left. 1 has about 80% gearwear left. 1 is poor with a partially cracked tooth.
7.) 5 of Mercury D tailcone bearing and seal assembly for propshaft assembly. 4 tailcones are good to near new with insitu bearings and seals. 1 can still be re-machined to re-new rear seal landing, loaded with Torringtons and used again.
8.) 2 of Mercury D tailcones with good threads. One is NOS new and the other had the prop eat it a bit as it did the seal and cone bearing carrier also here for sale.
9.) 2 of Mercury D waterpump cartridges with stainless steel covers and forward seal compression rings in good condition.
10.) 2 of Mercury D propshaft gears (unallocated) in used but very good condition with over 95% of wear left.
11.) 4 of Mercury D top of housing cartidges with seals. All in good condition. 2 for stock (Merc 55H) outboard use and 2 for Modified Outboard use for pipe/stick towers).
12.) 4 of Mercury D water pump impellers, 3 in good and i in fair conditions.
13. Mixed bag of Mercury D Quicksilver gearcase bearing shims and waterpump sealing rings.
14.) 2 of new Torrington for Merc D Quicky in major housing gearcase bearings.
15.) 4 of new Torrington for Merc D Quicky tailcone/propshaft support bearings.
16.) 4 of Mercury D Quicky driveshaft main ball bearing units, 2 are new and 2 are used. The 2 used bearings are both in good condition for re-use.
17.) 3 of Mercury D Quicky propshaft main bearings. All 3 have never been used.
18.) 6 of Mercury D Quicky propshaft/tailcome cartridge seals in new condition.
19.) Misc Mercury D Quicky water tube seals and washers.
20.) Misc Mercury D Quicky driveshaft gear bolts and geartop lock washers.
END OF ITEMS LIST.
If I knew I could reliably sell off all the parts, all parted out to the last item, so it would all be gone, I would, But if the interest is to pick off what ever until next spring and still leave me with odds and sods, I would prefer a single buyer/collector/racer for it all in one sale.
What parted out interests can be determined? What enblock sale interests are there out there? I am going to post everything on the BRF site with good Jpeg pictures as well as the listing the parts only here on hydroracernet, so I can see what might or can happen. If you have some kind of interest here, email me only at: anzani@mts.net
No phone calls please, only email me at: anzani@mts.net
The all inclusive list is as follows:
1.) Merc 55H stock dimensioned gearcase with loose rear cone threads, needs oversized cone and re-thread job. Good bearing areas throughout otherwise.
2.) Merc 55H stock dimensioned gearcase requiring the drivehaft bearing (Torrington roller) area be sleeve/bused and new Torrignton drivehaft bearings installed. Cone threads and other bearing areas are in good shape
3.) 2 Piece coupled Mercury Mark 55H driveshaft for standard height stock racing setup but can easily be cut and re-joined for shorter Modified applications/transoms.
4.) 3 of Mercury D propshafts with mounted gears. 2 shafts in good shape with their gears, 1 shaft is fair condition and likewise its prop gear.
5.) 3 of Mercury D propshaft mounted propshaft gears. All 3 are used but in condition from 95% to 90% and final down to about 80% of gear wear left.
6.) 4 of Mercury D driveshaft gears. 2 are in good used condition with 90%+ gear wear left. 1 has about 80% gearwear left. 1 is poor with a partially cracked tooth.
7.) 5 of Mercury D tailcone bearing and seal assembly for propshaft assembly. 4 tailcones are good to near new with insitu bearings and seals. 1 can still be re-machined to re-new rear seal landing, loaded with Torringtons and used again.
8.) 2 of Mercury D tailcones with good threads. One is NOS new and the other had the prop eat it a bit as it did the seal and cone bearing carrier also here for sale.
9.) 2 of Mercury D waterpump cartridges with stainless steel covers and forward seal compression rings in good condition.
10.) 2 of Mercury D propshaft gears (unallocated) in used but very good condition with over 95% of wear left.
11.) 4 of Mercury D top of housing cartidges with seals. All in good condition. 2 for stock (Merc 55H) outboard use and 2 for Modified Outboard use for pipe/stick towers).
12.) 4 of Mercury D water pump impellers, 3 in good and i in fair conditions.
13. Mixed bag of Mercury D Quicksilver gearcase bearing shims and waterpump sealing rings.
14.) 2 of new Torrington for Merc D Quicky in major housing gearcase bearings.
15.) 4 of new Torrington for Merc D Quicky tailcone/propshaft support bearings.
16.) 4 of Mercury D Quicky driveshaft main ball bearing units, 2 are new and 2 are used. The 2 used bearings are both in good condition for re-use.
17.) 3 of Mercury D Quicky propshaft main bearings. All 3 have never been used.
18.) 6 of Mercury D Quicky propshaft/tailcome cartridge seals in new condition.
19.) Misc Mercury D Quicky water tube seals and washers.
20.) Misc Mercury D Quicky driveshaft gear bolts and geartop lock washers.
END OF ITEMS LIST.
If I knew I could reliably sell off all the parts, all parted out to the last item, so it would all be gone, I would, But if the interest is to pick off what ever until next spring and still leave me with odds and sods, I would prefer a single buyer/collector/racer for it all in one sale.
What parted out interests can be determined? What enblock sale interests are there out there? I am going to post everything on the BRF site with good Jpeg pictures as well as the listing the parts only here on hydroracernet, so I can see what might or can happen. If you have some kind of interest here, email me only at: anzani@mts.net
No phone calls please, only email me at: anzani@mts.net
Comment