Unconfigured Ad Widget

Collapse

Announcement

Collapse
No announcement yet.

Wanted Hot Rod BSH/15H Drive Shaft.......

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Wanted Hot Rod BSH/15H Drive Shaft.......

    Lost my front bolt then nut fell off back of gear foot during Lemans start, pulled kill switch then lost drive shaft in mud. Eric Vanover got prop & gear foot out of water & mud for me. If any one has a Drive Shaft to sell please call me 732-266-7917 or PM me.
    Thank You!
    Earl Desiato
    Earl 11 J........ Dangerous when Wet Runne Craft- Earl said, " Driving a Runne Craft is like Cheating". Dude, ........ Where's My Boat!

  • #2
    Dang Earl,.........Ya left yer ......what ......"stuck" in the...where.....?

    "Dangerous when wet".....yep...yep..........

    Perhaps a call ta Racing Outboards?

    .
    Last edited by STEVE FRENCH; 06-17-2009, 02:54 AM.
    100N STEVE FRENCH > Nobody can hang with my STUFF!! >> http://www.youtube.com/watch?v=tna3B5zqHdk

    SEEEEEE YAAAAAA!!............In my WAKE!! .............100N>>

    Comment


    • #3
      Dangerous when wet".....yep...yep..........

      All right Steve Frenchy............It's on in AMH at Franklin Buddy!!!!!!!

      Sometimes I even wet down myself before the race to get it going!
      Earl 11 J........ Dangerous when Wet Runne Craft- Earl said, " Driving a Runne Craft is like Cheating". Dude, ........ Where's My Boat!

      Comment


      • #4
        When the "H" tower shattered under my 25MOD at the 2005 MODIFIED NATIONALS the gearfoot/prop and shaft went to the bottom at Franklin.

        Found the upper half of "shaft" a couple years later with 4x6 magnet from Harbor Freight tied to rope and drag'd behind pondtoon boat while cruise'n "Two Mile" lake with electric trol'n motor.........talk about yer needle in'a hay stack!........try'd a couple times since fer the foot/prop.....still no luck.....hey Eric Vanover!

        Anyone know of any fish'n motor splines that match the Hot-Rod power head?
        That you could cut and re-spline ta fit the coupler?

        Might also call Mouldner, Cooper, Carl Staron, Fibo, Sutherland........Brian Hendrick?

        100N STEVE FRENCH > Nobody can hang with my STUFF!! >> http://www.youtube.com/watch?v=tna3B5zqHdk

        SEEEEEE YAAAAAA!!............In my WAKE!! .............100N>>

        Comment


        • #5
          Thanks Steve, I found one! I just can't wait for that fine Franklin race & my Mod Friends!
          Earl 11 J........ Dangerous when Wet Runne Craft- Earl said, " Driving a Runne Craft is like Cheating". Dude, ........ Where's My Boat!

          Comment


          • #6
            Just got a 20 Hot-Rod from Howard P. for Archie Lewis......need a drive shaft.....Thought I saw a thread for new ones here recently?

            Link?

            Thanks 100N/Steve.............
            100N STEVE FRENCH > Nobody can hang with my STUFF!! >> http://www.youtube.com/watch?v=tna3B5zqHdk

            SEEEEEE YAAAAAA!!............In my WAKE!! .............100N>>

            Comment


            • #7
              Found it!.......... https://hydroracer.net/forums/showthread.php?t=19086
              100N STEVE FRENCH > Nobody can hang with my STUFF!! >> http://www.youtube.com/watch?v=tna3B5zqHdk

              SEEEEEE YAAAAAA!!............In my WAKE!! .............100N>>

              Comment


              • #8
                all new drive shafts are $90.00 each + shipping

                2 new omc A drive shaft
                2 new Hot-Rod stock drive shafts
                2 new Hot-Rod Mod, Short-Tower drive shafts
                1 of each. OMC 25ss and 25mod drive shafts, for long and short H-R tower with H-R gearcase
                1 omc 25ss/mod to H-R tower adaptor plate
                1 920 229 9253
                thanks
                53w

                Comment


                • #9
                  Steve

                  PM'd you.

                  Bill
                  Support your local club and local races.

                  Bill Pavlick

                  I'm just glad I'm not Michael Mackey - BPIII

                  Comment

                  Working...
                  X